Ebuynails.com

So this is how it arrives. You have the pallet, you have the base, you have the chair crop itself and then you have the n Of course, when you're assembling it, you want to start with the base. You can go ahead and get rid of the pallet whenever you feel you need to and to do this whole thing it takes about 30 minutes. I'm going to go ahead and open up all these boxes and we'll fast forward. So when I'm done. Alright, now that we've opened the Petticoat base, we have three important parts. The first one is the bar risers. Not all as far as I have this, but if you do have it, it's very important you need to install it. We'll put that aside for now and then we have the footrest inside this box which we'll open later. We have the base itself. We highly recommend you bring a friend. Eric, can you help me? Sure. Wow, because it is quite heavy. Go ahead and take the bar risers that you pulled up. Place them on top, aligning the holes with the tall side up. We Then the next thing, pull out the footrest on the back of the box. Underneath the footrest you'll see a little bag of screws and you'll want to grab a screw grab it for this next part. Open up the bag and then align the holes to the existing holes on the base. You'll want to base it For now, let's just set it on the lowest one so you can add the screws. Alright, I'm going to go ahead and add the screws. Put the washer on each. So, here's what the chair top will look I've seen it a lot of times. I'm going to go ahead and just remove this and we'll skip to the next section. Now that we've removed the chair top from the box, you'll notice that there are four things in the box. There's this bag of screws which will include the screws for the bar risers here. You have your power cord at the remote control and then you also have the manual. So, you want all of these things. I'll set them aside for the moment and now we'll begin attaching the chair top to the base. Okay, so for this next part we have the power cord, we have the remote control, we have the bar riser screws that we took out of that little package, we have the washers and then we have a 30mm wrench. So, it's very important to follow the same order that we're going to do this in. So, please watch carefully and have another person so that you can put the chair top onto the base. Alright, let's do this. Make sure you set the chair top directly on top of the bar risers and be very careful about setting it down so that you make sure you have it in the right spot. And then have your partner. . . Good. Have your partner continue to support the chair top as you do the next step, which is to apply the power cord. So, I'm going to go around to the back of the chair, plug it in. Okay, and then plugging in the remote is also quite simple. I'm going to have to plug it in. I'm going to get into space a little bit, sorry. And then pull this cable around the back and plug it in here. You will see a little connector here. Just make sure the pins line up and then there's this little movable washer. All you have to do is screw that in and that will help to secure the connection so that it doesn't come loose. Plug down and on. Go ahead and begin moving the chair back. That will allow access to the holes beneath it. If you have bar risers, it will allow access to the bar riser holes. If you don't, it will allow access to the holes on the chair top itself. So now that it's all the way in the rear position, go ahead and line up the holes to the bar risers on the chair base itself. The frame, I should say. We're going to need to move it around a little bit. All right. And then let's put the washer on. Then just push up the hole all the way in. And then we're going to need to align this next one. It might take a second to find the right position. So having your partner help is definitely very important here. There we go. Got that one. Let's move it back forward and do the rear screw holes as well. And of course, make sure when you're doing this that screw holes you're trying to target are the ones on the outside of the frame. And now that you have the first two screws installed, you want to bolt them in from the bottom inside of the tub. So grab a washer or a grep two washer and two nuts. We're going to go down below 30 millimeter wrench. And be careful to make sure that your partner has a nice firm grip on the chair. So with this one, wash your first on top. Should go in nice and easy. And then just use the wrench to tighten it up the last couple of turns. Can you hold on to it for me? Sure. Now with this screw? Yes. Okay, got that. Nice and tight. So let's grab our next one. Wash your eyes up. The little tongue. Can you hold this nut down? Sure. Okay. So let's move to the next step. And this next section. Move the chair according to the remote to where you align the holes on the bar riser and the frame here. So you can get a good close look. You'll want this long screw to through this hole on top of the frame, the hole in the bar riser and the whole tub. So you need to go through all those holes. So once you have the line, you can simply drop it in And then of course you're going to attach the nuts on the bottom. But before you do that, let's do the other side as well. So I'm going to have to come over here to get a good look at it. And it's a little bit hard to see. So you might need a light here. Okay. Now that you have only one screw hole left, just move the chair back or forth so that you have access to the final hole. Which is right there. Now that you can see it, make sure that you're going through all the holes. You might have to move it a little bit so that the holes are aligned. Let's just put these last two nuts on them and this part will be complete. Okay. Now the chair is attached to the base. So you can attach the cover set. Then grab the base section. See the two little screws here? Take off the screw caps. And then there's a connecting piece here. Just put that underneath the welded section in the middle and it will move right under it. And then align these two screws to the holes in the front. After they're aligned, you can attach the screws back on to secure the base. Okay. And then just grab your next section, which is the seat itself. See there are some coverings for the Velcro. To have Velcro work, you want to remove all of these. You'll also see that there's a wire here for the massage in the seat itself. Before you attach this, make sure the connecting wire is pulled out and visible underneath the base. So let's just set it down for now and then connect these two wires together. All right. Connect it. Now you can move this back and set it where it should be. All right. Seat is secured. And now we have the backrests. So if you want a softer massage, leave this on. If you want a more massage, you could feel a little bit stronger. You could take it off. We're going to leave ours on. And then remove the Velcro covers again. And you'll see the Velcro will connect to the alternating section on the back. Velcro cover on the side connects easily there. Hey, looking good. Almost done. Then the pillow. Look at the covers on this. Well, it's very nicely right here. And it's adjustable based on how far your customer's head is, what's the height of their upper body. And the last part, the side skirts. And these just go directly on the sides beneath the chair. Okay. Now you're fully assembled. You might go with a chair. And in case any of yous ever goes out, we've included you in the manual.