DIY Garage

Today we will build the best solution for storage and installation of work in garage in modern times. Relax and have fun. I started cutting a few boards, 2x4x8, on my ironing board. I set a blocking block to make the cuttings repeatable, because I just make a lot of elements about the same size. Each section of the shelf has 8 long boards and 30 inches of depth, to fit plastic containers that I bought. After the initial drilling of the holes in the 1-8 inch hole, I used two terrace screws and one second inch to connect all my elements. During work, I used a counter to make sure that everything is evenly balanced. And when I built 4 such shelves, I started by attaching the legs to the first shelf that I will lift. The legs have 800 dc, so I just bought a board of 8x2x4. There was no need to cut. I measured so that the second leg had 48 inches from the center. And don't worry about all these measurements, because in the article to which the link is in the description, I will have plans. But before I lifted the shelf, I drew a line on the wall, because I do it myself. It will be much easier for me, without the other person who will measure behind me. Two legs in the front of the shelf help hold everything in place. Then I used a few sporning to make sure that everything is balanced, when I drilled the holes and screwed them in. I saw people doing something similar when they were hanging the shelves and that's where the idea came from. I should have remembered that I used full 3-inch screws everywhere where I attached the shelf to the wall. The lifting of the second shelf was much easier, and the third one is even easier. Mainly because after putting a few sporning, I could attach them to the previous shelf as a point of lifting for the straight line. And as a result, I cut the sporning to have an additional pair of hands that kept everything safe and in the range of the hand. The next shelf sections are 48 inches long, not 8 inches, so I cut a few 2x4x4 pieces in half and built the shelf as the first time. And just It's not about holding the truck, but about not moving the items when you work in a different corner. I added an additional sporning in the shelf section for the workshop table, but I also mounted it the same as the rest. In the shelf section, I mounted the shelf as low as possible, I actually mounted it on the shelf, as you can see. I also used a flat drill to drill a hole and mount the wheel to the top of the shelf. And that's the end of the project about the 2x4x4 design. Looks good, I would The Zeo sprays provide safe and effective actions against all kinds of bugs. Thanks to 4 different formulas that scare the bugs, running, flying and multi-tasking, you are sure that you have the right tools for work. What I love about Zebo is that in contrast to the competitive products that use toxic chemicals, sprays because they contain popular etheric oils as active ingredients. It is therefore responsible for the bugs in the garage or under the terrace, and for the flying bugs that you do not want to spray with toxic chemicals on flying bugs. The bugs are attracted by UV and blue promenades, and then stick to the back side of the car. When the bug is full of bugs, you can remove the bug without touching the bugs and replace it with a new one. It is so simple, to learn more about the Zeo system at home, please click the link in the description. Thanks to Zeo, the wheels are made of 5. 8 inches of plastic wrap. This material is quite cheap and I gave it to the cuttings of the panel saw at home. Some of the 8-stop sections I could just place on the spot, I set the shelf's bar so that it would go right behind the wood and enter the styrofoam insulation that I used as a cutting board. It cost only about $ 10 and is much more pleasant than cutting on two-to-four blocks. As you all know, I cut these panels to a depth of 30 inches, which means that I had a lot of sections that I could use to make upper shelves. The use of these pieces turned out to be a really efficient way to make shelves, I think it is cheaper than using only two-to-four blocks. I raised the floor in the closet so that the mice had a smaller chance of entering there. I also cut some of the styrofoam insulation to make the side wall so that it would not collide with the workshop table. As I had already placed one of the cabinets on the workshop table, I decided to close the other one. Who knows, maybe I'll be able to place some nice shelves on the side of the tool. The last step to finish the project was to mount the lighting over the workshop table. I found 60-centimeter-long, connected LED strips. I bought them in Home Depot, but I found a better offer on Amazon and I'll leave the links to them in the description. The next step to finish the project is to place the lights on the side of the table. The lights are on the side of the table, so I'll leave the lights on the side of the table. Of course, it is not everything that comes out here. There will be a lot more things to do with time, but for good arrangement, I think that everything looks great. There are tools and things that you will use every day, places to put things in the shower and in the shower, and I'm going to put all the things I think about here, which we will use. I want to thank you once again for sponsoring this video. You can use the links in the description. And if you have any questions about this project, please If you On the screen, you can see a few more videos with links if you haven't seen them yet. Until next time,